In designing each Therm-O-Dor™, door size, mounting conditions, operation cycles, and wind load all impact the final door structure. Our goal is to help ensure a safe, operational door solution.

Strength and Rigidity

Achieved by the unequalled adhesion of the steel skins to the polyurethane core, the injected foam forms an even compact block that adheres strongly to every inch of the steel.

Thermal-break

Separates the outside and inside steel skins to reduce cold/heat conductivity and stop frost and moisture from collecting on the inside of the door.

Between-section Weatherseal

Air and wind infiltration are eliminated by the use of a continuous weatherseal, inserted between each section.

A Total Weatherseal System

The weatherseal system uses a "U"-shaped bottom weatherseal that conforms to minor floor irregularities and keeps out the weather. The perimeter of the door is sealed with the use of the steel/vinyl weatherstrip on the outside door jamb.

Virtually Maintenance-free

Door is finished with a baked-on, 2-coat polyester paint. The inside and outside skins are of a corrosion-resistant, hot-dipped galvanized steel.

Insulated Windows

Inserts are mounted in a high-impact polymer frame with sealed lites of glass.

Fast and Easy Installation

Made possible with easy-to-follow installation instructions that come with every door.

Quiet and Smooth Operation

Only heavy-duty hardware and top-quality rollers are used to ensure long life and smooth, quiet operation.

Painted Inside and Out

The continuous, seamless steel inside skin brightens the interior of the garage and is easy to keep clean. The exterior may be painted to any colour.

Warranty

The complete door is covered by a warranty for workmanship and material, as well as a 15-year warranty against cracking, splitting, or deterioration due to rust.

Warranty provides seven years of protection against delamination of the polyurethane foam from the steel skin on the panel; also there is a 1-year warranty against defects in workmanship and material. Contact us for complete warranty details.

Therm-O-Dor™ TD 138 offers a range of customized options that will enable you to meet virtually any application requirement. To learn how Steel-Craft can meet your needs in commercial overhead doors, please contact our office.

Door Face

Optional upgrades to components that are connected to the door face.

1. Graduated end hinge - available in increased gauge.
2. Track rollers - available in a variety of formats to meet your specifications.
3. Low lift hardware
4. Locks - 2 point interior, 2 point exterior.
5. Lift handle - 3 options available.
6. Vision lite windows - sealed glass: 23"x7"; 24"x12"; 34"x16"; consult your dealer on the wide variety of glass options.
7. Exhaust ports - available in various sizes.
8. Strutting - to increase wind load capacity.
9. Specialty high moisture area conversions

Guide

Optional upgrades to components that are related to the door guide. All lifts are available in 2" or 3" track.

• High lift - track and hardware that causes the door to rise vertically some distance above the top of the door opening before it levels out into a horizontal position. Available to meet a variety of height specifications.
• Vertical lift - track and hardware that causes the door to open vertically where no horizontal tracks are required. Available to meet all height specifications.
• Low lift double track - low headroom accessories which enable a door system to operate in minimal headroom conditions. Available to meet a variety of low headroom specifications.
• Full angle mount - available in Continuous and Reverse (1" overlap)

Lift

Optional upgrades to components that are related to the door lift.

• Torsion spring assembly - extensive cycle options are available to meet all specifications
• Torsion shaft - available in 1" solid where 1" tube is specified
• End bracket - 2-bolt flange bearing, available in 1"

End Stiles

    Single end

Hinges

    14ga single end

    11ga single end*

    14ga intermediate

Track Rollers

    2" 10 ball short stem

    3" 10 ball short stem

    2" 10 ball long stem*

    3" 10 ball long stem*

Speciality Track Rollers Long Stem

    2" nylon sealed bearing*

    3" UHMW sealed bearing*

    3" rubber sealed bearing*

    3" nylon stainless shaft*

Top Fixture

    Standard duty single

Bottom Corner Brackets

    Standard duty

Locks

    Sidelock

    Interior bar lock*

    Exterior keyed bar lock*

Handles

    Tub handle*

    PVC hand grip*

    Handle step plate*

Vision Lites

    23" x 7"*

    24" x 12"*

    34" x 16"*

Exhaust Ports

    3"*

    4"*

    5"*

Strutting

    DASMA PVCP standard

    Available to increase wind load capacities*

Weatherstrip - bottom

    3" U-type

    4" U-type*

Weatherstrip - top

    2" top flap

Weatherstrip - side

    Steel/vinyl

    PVC/vinyl*

Weatherstrip Retainer

    Bottom PVC V

    TOP PVC V

Guide Types

    Standard lift

    High lift*

    Vertical lift*

    Low lift double track*

    (All available to allow following the roof slope, if needed)

    Horizontal reinforcing engineered for specific size requirements.

Guide Mounting

    Bracket mount

    Angle mount continuous 13ga*

    Angle mount reverse 13ga*

Torsion Springs

    Standard 10,000 cycle

    Optional increased cycle*

Torsion Shafts

    (Engineered for specific requirements)

    14ga galvanized tube 1"

    Cold roll solid shaft 1"

Torsion Shaft Bearings

    Standard flange bearing 1"

    2 bolt cast flange bearing 1"*

 Torsion Bearing Plates

    (Engineered for specific weight requirements)

Therm-O-Dor™ TD 134 offers a selection of customized options to meet virtually any application requirement. For additional information on how Steel-Craft can meet your needs in commercial overhead doors, please contact our office.

Door Face

Optional upgrades to components that are connected to the door face.

1. Graduated end hinge - available in increased gauge.
2. Graduated double end hinge - available in increased gauge.
3. Track rollers - available in a variety of formats to meet your specifications.
4. Top fixtures - available in increased gauge.
5. Low lift hardware
6. Bottom corner bracket - available in increased gauge.
7. Failsafe bottom corner bracket
8. Locks - 2 point interior, 2 point exterior.
9. Lift handle - 3 options available.
10. Vision lite windows - sealed glass: 23"x7"; 24"x12"; 34"x16"; consult your dealer on the wide variety of glass options.
11. Aluminum - available in full view section; consult your dealer about insert options (glass, polycarbonate - double or triple wall).
12. Pass door
13. Exhaust ports - available in various sizes.
14. Strutting - to increase wind load capacity.
15. Aluminum L retainer
16. Specialty high moisture area conversions
17. Increased gauge section face

Guide

Optional upgrades to components that are related to the door guide. All lifts are available in 2" or 3" track.

• High lift - track and hardware that causes the door to rise vertically some distance above the top of the door opening before it levels out into a horizontal position. Available to meet a variety of height specifications.
• Vertical lift - track and hardware that causes the door to open vertically where no horizontal tracks are required. Available to meet all height specifications.
• Low lift double track - low headroom accessories which enable a door system to operate in minimal headroom conditions. Available to meet a variety of low headroom specifications.
• Moveable center posts
• Full angle mount - available in continuous and reverse (1" overlap).

Lift

Optional upgrades to components that are related to the door lift.

• Torsion spring assembly - extensive cycle options are available to meet all specifications.
• Torsion shaft - available in 1" solid where 1" tube is specified.
• 1-1/4" solid shaft
• End bracket - 2-bolt flange bearing, available in 1" and 1-1/4".

End Stiles

    Single end

    Double end 17'w+

Hinges

    14ga single end

    11ga single end*

    14ga double end 17'w+

    11ga double end 1000lbs

    14ga intermediate

Track Rollers

    2" 10 ball short stem

    3" 10 ball short stem

    2" 10 ball long stem

    3" 10 ball long stem

Speciality Track Rollers Long Stem

    2" nylon sealed bearing*

    3" UHMW sealed bearing*

    3" rubber sealed bearing*

    3" nylon stainless shaft*

Top Fixture

    Standard-duty single

    Standard-duty double 17'w+

    Heavy-duty double 1300lbs*

Bottom Corner Brackets

    Standard-duty

    Heavy-duty 1300lbs

    Heavy-duty fail safe*

Locks

    Side lock

    Interior bar lock*

    Exterior keyed bar lock*

Section Face 20ga*

Handles

    Tub handle*

    PVC hand grip*

    Handle step plate*

Vision Lites

    23" x 7"*

    24" x 12"*

    34" x 16"*

    Full-view aluminum*

Pass Door*

Exhaust Ports

    3"*

    4"*

    5"*

Strutting

    DASMA PVCP standard

    Available to increase wind load capacities*

Weatherstrip - Bottom

    3" U-type

    4" U-type*

Weatherstrip - Top

    2" top flap

    3" top flap - 17'w+

Weatherstrip - Side

    Steel/vinyl

    PVC/vinyl*

Weatherstrip Retainer

    Bottom PVC V

    Bottom aluminum L*

    TOP PVC V

Guide Types

    Standard lift

    High lift*

    Vertical lift*

    Low lift double track*

    (All available to allow following the roof slope if needed)

    Horizontal reinforcing engineered for specific size requirements

Guide Mounting

    Bracket mount

    Angle mount continuous 13ga*

    Angle mount reverse 13ga*

Torsion Springs

    Standard 10,000 cycle

    Optional increased cycle*

Torsion Shafts

    (Engineered for specific requirements)

    14ga galvanized tube 1"

    Cold roll solid shaft 1"

    Cold roll solid shaft 1-1/4"*

Torsion Shaft Bearings

    Standard flange bearing 1"

    Heavy-duty flange bearing 1"*

    2 bolt cast flange bearing 1"*

    Centre plate flange bearing 1-1/4"*

    End plate flange bearing 1-1/4"

    2 bolt cast flange bearing 1-1/4"*

Torsion Bearing Plates

(Engineered for specific weight requirements)